Most growers watch two numbers in their grow room: temperature and humidity. VPD β vapour pressure deficit β is what those two numbers mean together. It is a single figure, measured in kilopascals (kPa), that tells you how hard the air is pulling water out of your plants’ leaves. Get it right and your plants transpire steadily, drink and feed at a healthy rate, and grow at their best. Get it wrong and the same temperature and humidity that looked fine on paper can quietly stall growth, invite mould, or stress your plants into closing their stomata and shutting down photosynthesis.
If you are still setting up your first indoor grow, start with our general guide to how to grow weed β VPD control is one of the finer adjustments you add once the basics (light, water, airflow) are in place, not the first thing to worry about. But once your plants are healthy and growing, it is the single most useful climate number you can track.
What is VPD β and why does it matter for cannabis?
VPD is the difference between the saturation vapour pressure of the air β the maximum amount of water vapour the air can hold at its current temperature β and the actual vapour pressure, which is how much moisture is really in the air. Warm air can hold far more water vapour than cold air, so the same relative humidity means something very different at 20 Β°C than it does at 28 Β°C. That is exactly why relative humidity on its own is a blunt instrument: 60% RH at 20 Β°C and 60% RH at 28 Β°C are two different growing conditions, but VPD captures the difference in one number.
What the number actually describes is the pull on your plants’ leaves. Water evaporates from the leaf surface through tiny pores called stomata β a process called transpiration. That evaporation creates a gentle negative pressure that draws water (and with it, dissolved nutrients such as calcium and magnesium) up through the plant from the roots. Transpiration also cools the leaves and keeps the stomata open so carbon dioxide can enter for photosynthesis. Royal Queen Seeds puts it plainly in its VPD guide: transpiration keeps plants alive and developing well, and VPD has a big impact on this process.
The two failure modes are mirror images. When VPD is too low β the air is nearly saturated β the leaves can barely transpire. Water and nutrient movement slows, calcium-related problems appear, and the damp, still canopy becomes ideal territory for mould and mildew. When VPD is too high β the air is aggressively dry β the plant protects itself by closing its stomata. That stops water loss, but it also stops carbon dioxide from entering, so photosynthesis falls and growth stalls. Push it far enough and you get the visible signs of drought stress: leaf edges curling upward, crispy tips and slowed growth, even when the roots have plenty of water.
The science behind the temperature side of the equation is well established for cannabis itself. In a controlled study of cannabis gas exchange, Chandra and colleagues found that the maximum rate of photosynthesis occurred at 30 Β°C, and that temperatures above 30 Β°C had an adverse effect on stomatal conductance β the leaves’ ability to keep their pores open. A follow-up study of drug and fibre varieties put the optimum temperature for photosynthesis at 25β30 Β°C for most drug-type varieties. In other words, the temperature half of VPD is not a matter of opinion: cannabis photosynthesises best in the mid-to-high 20s, and hotter rooms actively work against it.
What is the ideal VPD for cannabis at each growth stage?
Young plants with small root systems cannot replace water quickly, so they need gentle, humid air β low VPD. As the plant grows and its root system and canopy expand, it can handle (and benefits from) a stronger pull, so the target rises. In flower, the priority shifts again: drier air keeps buds safe from mould, so VPD climbs higher still. The table below gives the ranges used across the major grower guides, with the temperature and humidity pairs that produce them.
| Growth stage | Ideal VPD (kPa) | Temperature (lights on) | Relative humidity |
|---|---|---|---|
| Seedling / clone | 0.4β0.8 | 24β27 Β°C | 65β75% |
| Early veg | 0.8β1.0 | 22β26 Β°C | 55β65% |
| Late veg | 1.0β1.2 | 22β26 Β°C | 50β60% |
| Early flower (weeks 1β4) | 1.0β1.3 | 20β24 Β°C | 45β55% |
| Late flower (week 5+) | 1.2β1.5 | 18β23 Β°C | 40β50% |
A few notes on the numbers. First, the ranges above are the consensus across grower guides, but they are grower practice anchored in photosynthesis and disease research β dedicated cannabis VPD trials are still scarce, so treat the bands as targets to aim for, not laboratory constants. Second, Royal Queen Seeds pushes late flower a little further, recommending 1.4β1.6 kPa in the middle and later flowering stage to fight off fungal threats β but it also warns never to let VPD exceed 1.6 kPa. If your room is already at 1.4 kPa in late flower, you are in the right territory either way; do not chase the extra 0.2 kPa if it means stressing the plants. Third, the transition matters more than the exact number: move gradually between stages rather than jumping from 0.8 to 1.3 kPa overnight. Plants adjust to a changing climate; a sudden swing is a stress event.
One more range worth knowing is the lights-off one. When the lights go out, temperatures fall and relative humidity rises, so VPD drops β sometimes sharply. In flower, never let humidity climb above 60% during the dark period, and a common lights-off VPD target is 0.8β1.2 kPa: low enough to let the plant recover, high enough to keep the buds from sitting in damp air all night. If your night-time humidity is the problem, that is usually a dehumidifier or extraction issue, not a daytime settings issue.
How do you measure and calculate VPD?
You need two readings: air temperature and relative humidity, taken at canopy height β where the leaves actually are, not at the floor or near the intake vent. A basic digital thermo-hygrometer hung at canopy level is enough to start. Better setups use a sensor with a data log, or an environmental controller that calculates VPD live and switches the humidifier, dehumidifier and extraction fan automatically.
The calculation itself is simple once you know the formula. First work out the saturation vapour pressure (SVP) for your temperature, using the Tetens equation:
SVP (kPa) = 0.6108 Γ e^(17.27 Γ T / (T + 237.3)), where T is temperature in Β°C.
Then: VPD = SVP Γ (1 β RH / 100), where RH is relative humidity as a percentage.
A worked example: a grow room at 25 Β°C and 55% RH. The saturation vapour pressure at 25 Β°C is 3.17 kPa. Multiply by (1 β 0.55) and you get 3.17 Γ 0.45 = 1.43 kPa β ideal for late veg or early flower. Drop the humidity to 45% at the same temperature and VPD rises to 1.74 kPa, which is too high for any stage. Raise the humidity to 65% instead and it falls to 1.11 kPa, right for veg. The same temperature, three different climates β that is the point of the number.
There is one refinement worth knowing: leaf VPD versus air VPD. Strictly speaking, VPD should be calculated from the temperature of the leaf surface, not the air around it, because transpiration happens at the leaf. Leaves are usually 1β3 Β°C cooler than the surrounding air because evaporation cools them, though under strong LED lighting with good airflow a leaf can sit close to air temperature. Most VPD charts assume the leaf is about 1β2 Β°C cooler than the air, which is close enough for a home grow. If you want precision, an infrared thermometer pointed at the canopy gives you a real leaf temperature β then use that temperature in the formula instead of the air temperature. If the leaf is warmer than the chart assumes, your real VPD is roughly 0.2β0.3 kPa higher than the chart says.
How to raise VPD when it is too low
Low VPD means the air is too humid for the temperature β the most common situation in a small tent full of transpiring plants, and the most dangerous in flower. Your levers, in order of usefulness:
- Run a dehumidifier. The direct fix. Size it to the tent: a small room dehumidifier is enough for a single tent, but a sealed room with several large plants needs a proper unit with a drain hose, not a tabletop model you empty by hand. Set it to your target humidity for the stage and let it hold the line.
- Increase extraction and airflow. A stronger exhaust fan pulls humid air out of the tent and brings drier room air in. Inside the tent, oscillating fans keep air moving across the canopy so no pocket of still, damp air sits inside a dense cola. Airflow alone will not fix a genuinely humid room, but without it even a dehumidifier leaves wet spots. Good airflow is also why pruning a weed plant to open up the canopy matters β fewer leaves crammed together means less trapped humidity around the buds.
- Raise the temperature slightly. Warmer air holds more moisture, so the same absolute amount of water vapour produces a higher VPD. A degree or two from a heater or a light dimmed up can lift VPD without touching the humidity β but stay inside the 25β30 Β°C photosynthesis sweet spot, and remember that heat plus low humidity is a fast route to the high-VPD problems below.
- Water less, and earlier in the day. Freshly watered pots and wet soil surfaces pump humidity into the tent for hours. Watering at the start of the light cycle gives the room the whole day to dry out, and letting the top of the medium dry between waterings removes a constant source of moisture.
- Defoliate lightly in flower. Removing a few large fan leaves that shade bud sites or block airflow reduces the total leaf area pumping moisture into the air and lets air move through the canopy. Do it sparingly β leaves are the plant’s solar panels β and never strip a plant bare.
Fix low VPD quickly in flower, because this is where the cost is highest. Dense buds sitting in humid, still air are exactly where bud rot starts, and by the time you can see it from the outside the inside of the bud is usually already gone. Our guide to what bud rot looks like shows the early signs β grey fuzz, brown mushy tissue near the stem, a musty smell β and if you find it, that bud goes in the bin.
How to lower VPD when it is too high
High VPD means the air is too dry for the temperature β common in winter, in air-conditioned rooms, and in tents with powerful extraction. The plant’s response is to close its stomata, which slows photosynthesis and growth, and in a young plant with a small root system it can cause wilting even when the soil is wet. Your levers:
- Run a humidifier. Again, the direct fix. An ultrasonic humidifier is the usual choice for a tent: cheap, effective, and easy to put on a humidity controller so it switches off at your target. Use clean water β tap water in a humidifier leaves a fine white mineral dust on leaves and equipment. In a very small tent, a tray of water or damp towels can nudge humidity up, but it is not a substitute for a real humidifier in a dry room.
- Cool the room. Lowering the temperature reduces the air’s capacity to hold moisture, which lowers VPD at the same humidity. An air conditioner, a cooler intake, or simply running lights at night when the ambient air is cooler all help. This is also why many growers run their lights overnight in summer β the coolest hours do the climate work for free.
- Slow the extraction fan. If your exhaust is pulling humid air out faster than the plants can replace it, the tent dries out. A fan speed controller (or a controller that runs the fan on humidity) keeps the air exchange you need without over-drying the room.
- Use a humidity dome for seedlings and clones. A cutting has no roots at all, so it can only take in water through its leaves β it needs near-saturated air, around 0.4β0.8 kPa and 65β75% RH, until roots form. A clear dome over a tray holds that microclimate with almost no equipment.
- Mist sparingly, and only in veg. A light foliar mist raises humidity briefly, but wet leaves in flower are an invitation to mould. Treat misting as a stopgap, not a climate strategy.
One caution: do not solve high VPD by soaking the room. Humidity above 70% in veg is workable, but the moment you cross into flower, sustained high humidity trades one problem (slow growth) for a worse one (mould). In late flower, accept a slightly high VPD β up to 1.5 or 1.6 kPa β rather than pushing humidity up to bring it down.
Common VPD mistakes β and how to avoid them
Chasing a single number instead of a range. VPD targets are bands, not bullseyes. A seedling at 0.6 kPa and one at 0.75 kPa are both fine. Growers who adjust equipment every time the reading moves 0.1 kPa end up with a room that swings wildly, which is worse than a steady reading at the edge of the band. Set your controller to a range and let it breathe.
Measuring in the wrong place. A sensor on the tent wall, near the floor, or next to the intake tells you about that spot, not about the canopy. Temperature can vary several degrees between the top of the canopy (under the light) and the floor. Hang the sensor at canopy height, in the middle of the plants, and move it up as the plants grow.
Forgetting the lights-off swing. The most common VPD failure is not the daytime number at all β it is the night. Lights go out, temperature falls 3β6 Β°C, relative humidity climbs, and VPD collapses while you are asleep. Check your night-time readings for a week before deciding your climate is dialled in. If nights are the problem, a dehumidifier on a humidistat, or a small heater to hold the night temperature up, fixes it.
Using air temperature instead of leaf temperature. Most charts assume leaves are about 1β2 Β°C cooler than the air. Under strong LEDs with good airflow that assumption mostly holds, but if your leaves are running warm β lights too close, poor airflow β your real VPD is higher than the chart says, and you may be stressing plants you think are in range. An infrared thermometer costs little and removes the guesswork.
Treating VPD as a magic yield button. VPD is one variable among many. A plant with poor light, bad watering or a nutrient problem will not be saved by perfect VPD, and chasing VPD while ignoring the basics is wasted effort. As the Growers Network’s Myles Lewis puts it, you can use VPD to steer plant growth β but if you do not really know what you are doing, you can really damage things. Get light, water and airflow right first, then use VPD to fine-tune.
Ignoring the strain. Different cultivars respond differently to the same climate. Some landrace sativas tolerate heat and dry air that would stress a dense indica. If you run several strains in one room, aim for the middle of the band and watch the most sensitive plant, not the average.
Frequently asked questions
What is the ideal VPD for cannabis?
It depends on the growth stage: 0.4β0.8 kPa for seedlings and clones, 0.8β1.2 kPa in veg, 1.0β1.3 kPa in early flower and 1.2β1.5 kPa in late flower. Never let VPD exceed 1.6 kPa at any stage. These are the consensus ranges across grower guides; Royal Queen Seeds recommends up to 1.4β1.6 kPa in mid to late flower.
How do I raise VPD in my grow tent?
Run a dehumidifier, increase extraction and airflow, raise the temperature a degree or two, and water earlier in the day so the room dries out during lights-on. The dehumidifier is the most direct tool; airflow matters because it stops damp pockets forming inside a dense canopy.
How do I lower VPD in my grow tent?
Run a humidifier, cool the room, and slow the extraction fan so humid air is not pulled out faster than the plants can replace it. For seedlings and clones, a humidity dome holds the moist microclimate they need. Do not push humidity above 60% in flower just to lower VPD β accept a slightly high VPD instead.
What happens if VPD is too high?
The plant closes its stomata to stop water loss, which also stops carbon dioxide entering β so photosynthesis and growth slow down. Leaves curl upward at the edges, tips turn crispy, and young plants can wilt even with wet soil. Sustained VPD above 1.6 kPa stresses the plant and can trigger nutrient uptake problems, because the transpiration stream that carries nutrients is disrupted.
What happens if VPD is too low?
Transpiration nearly stops, so water and nutrient movement through the plant slows and calcium-related deficiencies can appear. Worse, the damp, still air is ideal for mould and mildew β powdery mildew on leaves and bud rot inside dense flowers. In flower, low VPD (high humidity) is the single biggest environmental risk to the harvest.
Sources
- Royal Queen Seeds (2026). How can vapour pressure deficit (VPD) boost cannabis yields? https://www.royalqueenseeds.com/blog-vpd-how-can-vapour-pressure-deficit-boost-cannabis-yields-n893 β grower guide on VPD ranges by stage (seedling 0.4β0.8 kPa, veg 0.8β1.2 kPa, early flower 1.0β1.2 kPa, mid/late flower 1.4β1.6 kPa, never above 1.6 kPa), transpiration, stomatal closure and control methods.
- Chandra, S., Lata, H., Khan, I. A., & ElSohly, M. A. (2008). Photosynthetic response of Cannabis sativa L. to variations in photosynthetic photon flux densities, temperature and CO2 conditions. Physiology and Molecular Biology of Plants, 14(4), 299β306. https://doi.org/10.1007/s12298-008-0027-x β peer-reviewed study: maximum photosynthesis at 30 Β°C, adverse effects on stomatal conductance above 30 Β°C.
- Growers Network (n.d.). Vapor pressure deficit. https://growersnetwork.org/cultivation/vapor-pressure-differential/ β interview with Myles Lewis on why VPD beats relative humidity as a stress indicator, stage-specific control, and equipment (humidifiers, dehumidifiers, controllers, airflow).
Educational content only β not medical advice. Cannabis laws vary by region.
Last updated: 7 November 2026
